NEC SigmaBlade AD106a Betriebsanweisung Seite 67
- Seite / 162
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Configuring Your Storage and I/O Blade 4-23
Default settings and their explanation
Item Default Description Change
Battery Backup Present
None
Displays Properties of additional
battery.
• When battery is installed: Present
• When battery is not installed: None
–
Set Factory Defaults No – Prohibited
*1
Cluster Mode Disabled – Prohibited
Rebuild Rate 30 Recommended value: 30 Permitted
BGI Rate 30 Recommended value: 30 Permitted
CC Rate 30 Recommended value: 30 Permitted
Reconstruction Rate 30 Recommended value: 30 Permitted
Controller BIOS Enabled – Prohibited
NCQ Disabled – Prohibited
Coercion Mode None – Prohibited
S.M.A.R.T Polling 300 – Prohibited
Alarm Control Disabled Disabled: Does not issue an alarm.
Enabled: Issues an alarm.
Silence: Stops an alarm if beeped.
Permitted
*2
Patrol Read Rate 30 Recommended value: 30 Permitted
Cache Flush
Interval
4 – Prohibited
Spinup Drive Count 2 – Prohibited
Spinup Delay 12 – Prohibited
StopOnError Disabled – Prohibited
Drive Powersave Disabled – Prohibited
Stop CC On Error No
Yes
Specify the operation at error detection
in Consistency Check.
No: Recover and resume.
Yes: Abort
Permitted
Maintain PD Fail
History
Enabled – Prohibited
Schedule CC Supported Set the scheduled consistency check. Permitted
CC Frequency Disabled Set the interval of scheduled
consistency check.
*3
Disabled: Disables the scheduled
consistency check.
Continuous: Checks consistency
continuously.
Hourly: Checks consistency every hour.
Daily: Checks consistency every day.
Weekly: Checks consistency every
week (recommended value).
Monthly: Checks consistency every
month (recommended value).
Permitted
CC Start Time 12:00 AM Set the time to start the first consistency
check.
Permitted
- NEC Express5800 Series 1
- Storage and I/O Blade AD106a 1
- User's Guide 1
- SAFETY INDICATIONS 3
- Attentions 4
- Prohibited Actions 4
- Mandatory Action 4
- Trademarks 6
- ABOUT THIS USER'S GUIDE 8
- IN THE PACKAGE 9
- CONTENTS 10
- Chapter 1 13
- SAFETY NOTES 14
- Do not step on the cable 15
- FOR PROPER OPERATION 17
- TRANSFER TO THIRD PARTY 19
- DISPOSAL AND CONSUMABLES 20
- USER SUPPORT 21
- Advice for Health 22
- Chapter 2 23
- OVERVIEW 24
- STANDARD FEATURES 25
- Front View 26
- Internal View 27
- External View 28
- Lamp Indications 30
- STATUS Lamp 31
- LAN (1 - 2) Link/Access Lamps 32
- DISK ACCESS Lamp 32
- Device Identification 34
- Chapter 3 35
- Check of MAC Address 36
- Installation Order 37
- SIGMABLADE-M 38
- Installing in Blade Enclosure 39
- Joint bracket for AD106a 42
- Installation and Removal 43
- IMPORTANT: 44
- Chapter 4 45
- RAID SYSTEM CONFIGURATION 46
- RAID Levels 49
- Removed physical drive 55
- Migration only 55
- Migration with addition 55
- Before Using WebBIOS 58
- Using WebBIOS 61
- Main Menu 62
- WebBIOS Menu 63
- Controller Properties 65
- How to change setting value 69
- Scan Devices 70
- Virtual Drives 71
- Physical Drive Properties 73
- 3. Click [Go] 73
- Configuration Wizard 75
- Controller Selection 75
- Physical View / Logical View 75
- Configuring Virtual Drive 77
- DG is added to Span 80
- Configure SPAN 85
- [Accept] 87
- Parameters for VD Definition 90
- Operation of Various Features 93
- Manual Rebuild 95
- Setting Hot Spare 99
- "DED HOTSPARE" 100
- Reconstruction 102
- Slow Initialize 105
- Number and ID 106
- Setting of Priority 107
- Chapter 5 109
- Setup of teaming 110
- Network Driver 111
- Optional Network Board Driver 111
- Setting WOL 111
- Setting Receive Side Scaling 112
- TCP Chimney Offload 113
- Receive-side Scaling 113
- NetDMA 113
- SETTING FOR SOLVING PROBLEMS 115
- UPDATING THE SYSTEM 118
- Chapter 6 119
- Chapter 7 121
- SYSTEM DIAGNOSTICS 122
- RELOCATING/STORING THE UNIT 123
- Chapter 8 125
- SYSTEM VIEWERS 126
- ERROR MESSAGES 127
- 8-4 Troubleshooting 128
- Troubleshooting 8-5 129
- Error Messages on Virtual LCD 130
- Troubleshooting 8-7 131
- 8-8 Troubleshooting 132
- SOLVING PROBLEMS 133
- Fail to power-off: 134
- Fail to start OS: 135
- Problems with Windows 137
- Server 2003 x64 Editions: 139
- Server 2003 R2 142
- COLLECTING EVENT LOG 146
- MAINTENANCE TOOLS 146
- Chapter 9 147
- ANTI-STATIC MEASURES 149
- PREPARATION FOR INSTALLATION 151
- Mezzanine Card 152
- Hard Disk Drive 157
- Appendix A 161
- A-2 Specifications 162
Verwandte Produkte und Handbücher für RAID-Kontroller NEC SigmaBlade AD106a
RAID-Kontroller NEC N8103-89 Bedienungsanleitung
(128 Seiten)
(128 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.068 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern