NEC Express5800/GT110b Betriebsanweisung Seite 260
- Seite / 494
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
8-14 Troubleshooting
Fail to access to the DVD/CD-ROM:
Is the DVD/CD-ROM properly set in the optical disk drive tray?
→ The tray is provided with a holder to secure the DVD/CD-ROM. Make sure that
the DVD/CD-ROM is placed properly in the holder.
Is the DVD/CD-ROM applicable to the server?
→ The DVD/CD-ROM for Macintosh is not available for use.
→ For the disk which does not conform to the CD standard, the playback of such a
disk with the optical disk drive is not guaranteed.
The POWER/SLEEP lamp goes on when the power cord is connected:
→ When the server receives an AC power after the power cord is connected, the
POWER/SLEEP lamp goes on. This is a normal operation of the server, not a fault.
The lamp will go off when DC power is turned on, and then off.
Inserted the correct DVD/CD-ROM but the message like the following is displayed:
The DVD/CD-ROM is not inserted or the wrong DVD/CD-ROM is inserted.
Please insert the correct DVD/CD-ROM.
OK
Is the data side of the DVD/CD-ROM dirty or injured?
→ Take the DVD/CD-ROM out of the optical disk drive, confirm that it is not dirty
or injured, reset and click [OK].
Fail to access the hard disk drive:
(Refer to the documentation supplied with the RAID Controller.)
Is the hard disk drive applicable to the server?
→ Operation of any device that is not authorized by NEC is not guaranteed.
Is the hard disk drive properly installed?
→ See Chapter 9.
- NEC Express5800/GT110b 1
- EXP260A 1
- User's Guide 1
- SAFETY INDICATIONS 3
- Attentions 4
- Prohibited Actions 4
- Mandatory Action 4
- Trademarks 6
- PREFACE 7
- ABOUT THIS USER'S GUIDE 8
- IN THE PACKAGE 9
- CONTENTS 10
- Chapter 1 17
- WARNING LABELS 18
- SAFETY NOTES 19
- During Operation 24
- FOR PROPER OPERATION 25
- TRANSFER TO THIRD PARTY 26
- DISPOSAL AND CONSUMABLES 27
- USER SUPPORT 27
- Hard disk drive (HDD) 28
- Solid state drive (SSD) 28
- Advice for Health 29
- Chapter 2 31
- OVERVIEW 32
- SYSTEM CHASSIS 33
- 2-4 General Description 34
- Rear View 35
- 2-6 General Description 36
- Internal View 37
- Mother Board 40
- STANDARD FEATURES 41
- AC LINK Feature 42
- Security 42
- (Silent Mode) 43
- NEC ESMPRO 44
- Maintenance Tools 44
- System Diagnostic Utility 44
- USING YOUR SERVER 45
- Network 47
- Power Off 49
- SLEEP Switch 49
- Writing Data onto Disk 51
- About Write Error 51
- Before Writing onto Disk 51
- 2-22 General Description 52
- Flash FDD 53
- Chapter 3 55
- SETUP FLOW 56
- UNPACKING THE SYSTEM 57
- INSTALLING OPTIONAL DEVICES 57
- SELECTING SERVER SITE 58
- CONNECTING POWER CORD 62
- TURNING ON THE SERVER 64
- INSTALLING OPERATING SYSTEM 66
- INSTALLING UTILITIES 66
- Chapter 4 67
- Starting SETUP Utility 69
- Configuration Examples 71
- DIMM #2 72
- DIMM #4 72
- DIMM #1 72
- DIMM #3 72
- 4-8 Configuring Your Server 74
- Processor Settings 77
- Advanced 78
- System Management 85
- Console Redirection 86
- DMI Event Logging 86
- RAID SYSTEM CONFIGURATION 89
- Enabling RAID Feature 94
- (SWRAID) 95
- Setup Utility 96
- Menu Tree 98
- 6. Press Space 100
- Parameter Remarks 102
- SPAN=NO Does not set span 102
- SPAN=YES Sets span 102
- STRIPING of RAID1 102
- IMPORTANT: 103
- Perform Check Consistency 107
- Number and ID 109
- Adapter and RAID Controller 109
- Logical Drive 109
- Disk Array 110
- Setting of Priority 110
- Chapter 5 115
- About Express Setup 116
- Windows Server 2008 R2 117
- Mounting MO Device 118
- About Removable Media 118
- Connecting Hard Disk Drive 119
- Flow of Setup 122
- About partition size 128
- 16. Save the parameters 132
- 22. Log on to the system 134
- Setup Team 137
- Adapter Fault Tolerance 138
- Adaptive Load Balancing 138
- Static Link Aggregation 138
- Switch Fault Tolerance 138
- 11. Restart the system 139
- Setting item Change setting 140
- Setting for Solving Problems 141
- BitLocker 141
- Windows Server 2008 142
- Windows Server 2008 143
- Other controllers 143
- 23. Log on to the system 160
- Windows Server 2003 169
- Installing the Service Pack 173
- FLOW OF SETUP 174
- Setup of teaming 185
- 6. Click [Next] 186
- 7. Click [Install] 186
- Network Driver 187
- Setting WOL 191
- 1. Start Device Manager 192
- 4. Click [OK] 192
- 5. Restart the system 192
- Graphics Accelerator Driver 193
- SETTING FOR SOLVING PROBLEMS 194
- 2. Click [Processes] tab 201
- Network Monitor 204
- Do you want to continue? 207
- UPDATING THE SYSTEM 208
- Chapter 6 211
- NEC EXPRESSBUILDER 212
- OS installation 213
- Tool menu (Normal mode) 214
- Autorun Menu 216
- PARAMETER FILE CREATOR 217
- Parameter File 218
- [Windows Server 2003] 223
- 14. Save the parameters 229
- 15. Saved to a floppy disk 230
- Server failures 231
- Performance 231
- NEC ExpressUpdate Agent 232
- Universal RAID Utility 233
- Easy Configuration 234
- Windows Server 2003 235
- Using Utility 236
- Uninstallation 236
- Chapter 7 237
- CLEANING 238
- Cleaning the Server 239
- Cleaning the Keyboard/Mouse 239
- Cleaning Disc 240
- SYSTEM DIAGNOSTICS 241
- Enduser Menu 244
- <Test Result> 244
- 7-10 Maintenance 246
- Chapter 8 247
- SYSTEM VIEWERS 248
- Troubleshooting 8-3 249
- POWER/SLEEP Lamp 250
- DISK ACCESS Lamp 250
- Access Lamp 250
- LINK/ACT Lamp 250
- 1000/100/10 Lamp 250
- ERROR MESSAGES 251
- POST Error Messages 252
- Troubleshooting 8-7 253
- Beep Codes 254
- DMI Event Log 255
- 8-10 Troubleshooting 256
- SOLVING PROBLEMS 257
- Problems with Windows 263
- PCI Express Correctable 272
- Problems with Express Setup 274
- A hard disk drive fails: 277
- Collecting Event Log 280
- Memory Dump 281
- RECOVERY FOR Windows SYSTEM 282
- MAINTENANCE TOOLS 283
- Troubleshooting 8-39 285
- BIOS/FW Updating 287
- ROM-DOS startup FD 287
- Test and diagnostics 287
- System Management 287
- RESETTING THE SERVER 288
- FORCED SHUTDOWN 289
- 8-44 Troubleshooting 290
- Chapter 9 291
- STATIC PRECAUTIONS 293
- 1. Shut down the OS 294
- Side Cover 295
- 3. Loosen the two screws 296
- Upgrading Your Server 9-7 297
- デスクトップの表示.scf 298
- Front Bezel 299
- Installation 300
- 3.5-inch Hard Disk Drive 301
- 3. Remove the side cover 302
- 12. Assemble the server 306
- 2.5-inch Hard disk 310
- 11. Assemble the server 312
- NOTES: 313
- 0 SLT=1 SLT=1 314
- 1 SLT=2 SLT=2 314
- 2 SLT=3 SLT=3 314
- 3 SLT=4 SLT=4 314
- Slot number 314
- Select/set a RAID level 317
- Notes on use 318
- Remove the screw 319
- Slide out the plate in 319
- Markings 320
- バッテリのプレートが上面となる状態で… 324
- 表面にドット無し 324
- PCI Board 326
- √: Available, –: Unavailable 327
- PCI guide rail 330
- 8. Assemble the server 331
- Internal COM connector 334
- Installation Order and Notes 337
- Key slot 338
- File Device 340
- 5.25-inch Device 341
- 9-52 Upgrading Your Server 342
- Dedicated screws 343
- 10. Assemble the server 344
- Optical Disk Drive 346
- Removal 348
- Chapter 10 349
- INTERFACE CABLES 350
- Mother board 353
- LED cable 353
- Installation of SCSI Device 354
- Installation of SAS Device 355
- POWER CABLES 357
- Appendix A 359
- A-2 Specifications 360
- Appendix B 361
- DVD/CD-ROM 364
- Tape Media 364
- Keyboard 365
- DragDouble-clickClick 366
- Appendix C 367
- C-2 IRQ 368
- Appendix D 369
- 1. Turn on your system 377
- 3. Restart the system 377
- More than 6 characters 383
- 19. Log on to the system 384
- Updating the System 386
- LAN Driver and PROSet 389
- Adapter Fault Tolerance 392
- Adaptive Load Balancing 392
- Static Link Aggregation 392
- Switch Fault Tolerance 392
- 3. Click [Setting] tab 393
- About Windows Activation 396
- Activate Windows 398
- Appendix E 401
- Install Windows – Insert Disc 415
- OK Cancel 415
- Appendix F 435
- EXPRESSBUILDER" 438
- The system has been updated 451
- Setup of teaming 453
- Appendix G 465
- Appendix H 489
- Appendix I 491
- (factory-installe 492
- Software 493
Verwandte Produkte und Handbücher für Server NEC Express5800/GT110b
Server NEC Express5800/320Ma Betriebsanweisung
(86 Seiten)
(86 Seiten)
Server NEC Express5800/R120d-2E SR Betriebsanweisung
(151 Seiten)
(151 Seiten)
Server NEC Express5800/HV8600 Betriebsanweisung
(204 Seiten)
(204 Seiten)
Server NEC Express5800/120Lf Betriebsanweisung
(198 Seiten)
(198 Seiten)
Server NEC Express5800/120Rh-1 Betriebsanweisung
(190 Seiten)
(190 Seiten)
Server NEC Express5800/T110g-S Betriebsanweisung
(128 Seiten)
(128 Seiten)
Server NEC Express5800/120Rg-2 Betriebsanweisung
(338 Seiten)
(338 Seiten)
Server NEC Express5800/120Rj-2 Betriebsanweisung
(206 Seiten)
(206 Seiten)
Server NEC SigmaBlade B140a-T Betriebsanweisung
(376 Seiten)
(376 Seiten)
Server NEC Express5800/120Li Betriebsanweisung
(344 Seiten)
(344 Seiten)
Server NEC Express5800/1160Xd Betriebsanweisung
(214 Seiten)
(214 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.067 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern