NEC MDview 213 Betriebsanweisung PDF herunterladen (Seite 25)

English

English-23

Tag2 R-H.position Adjusts the position of the red component of the image. Press “Left” or “Right” to adjust.

(Analog input only)

G-H.position Adjusts the position of the green component of the image. Press “Left” or “Right” to adjust.

(Analog input only)

B-H.position Adjusts the position of the blue component of the image. Press “Left” or “Right” to adjust.

(Analog input only)

R-FINE Adjusts the “FINE” setting of the RED component of the image.

(Analog input only) Press “Left” or “Right” to adjust.

G-FINE Adjusts the “FINE” setting of the GREEN component of the image.

(Analog input only) Press “Left” or “Right” to adjust.

B-FINE Adjusts the “FINE” setting of the BLUE component of the image.

(Analog input only) Press “Left” or “Right” to adjust.

R-SHARPNESS Adjusts the sharpness of the red component of the image. Press “Left” or “Right” to adjust.

(Analog input only)

G-SHARPNESS Adjusts the sharpness of the green component of the image.

(Analog input only) Press “Left” or “Right” to adjust.

B-SHARPNESS Adjusts the sharpness of the blue component of the image.

(Analog input only) Press “Left” or “Right” to adjust.

DVI Long Cable Compensates for image degradation caused by using a long DVI cable.

(Digital input only) There are 4 possible settings, with “0” being the lowest level of compensation and

“3” being the highest level. The default setting is “1”.

Tag3 Auto Adjust Automatically adjusts the Image Position and H.Size settings and Fine settings.

(Analog input only) Press “SELECT” to activate Auto Adjustment.

Signal Adjust Determines when the auto adjustment is activated automatically.

(Analog input only) The choices are “SIMPLE” and “FULL”. Press “Left” or “Right” to select.

Auto Adjust Level Determines the automatic adjustment level for Auto Adjust. The choices are “SIMPLE”,

(Analog input only) “FULL” and “DETAIL”. Press “Left” or “Right” to select. Refer to the below table.

A-NTAA SW The Advanced No Touch Auto Adjust function is able to recognize new signals even when

(Analog input only) neither the resolution nor the refresh rate has changed. If several PCs are connected to

the monitor, and each transmit very similar (or even the same) signals in terms of

resolution and refresh rates, the monitor recognizes that there is a new signal and

automatically optimizes the picture without the need for any action on the part of the user.

OFF: A-NTAA is disabled.

ON: If a change in signal is detected A-NTAA will adjust the monitor to the optimal settings

for the new signal. If no change in the signal is detected then A-NTAA does not activate.

The screen will be blank while the monitor optimizes the signal.

OPTION: Functions the same as ON, except that the screen does not go blank when the

monitor makes adjustments for changes in signal, allowing the monitor to display the new

signal faster. When using an external switching device to connect 2 or more PCs to the

monitor, using the ON or OPTION settings is suitable.

Tag4 H. Position Controls Horizontal Image Position within the display area of the LCD.

Press “Left” or “Right” to adjust.

V. Position Controls Vertical Image Position within the display area of the LCD.

Press “Left” or “Right” to adjust.

H-size, Fine, H/V Position Contrast

SIMPLE O X

FULL O O

O: Automatic Adjustment X: No Automatic Adjustment

NOTE: Automatic Adjustment does not work at resolutions less than 800x600 resolution.

Size, Fine, Position Contrast Black Level, Time

Long cable capability**

SIMPLE O X X 1 second

FULL O O X 1.5 seconds

DETAIL* O O O 5 seconds

O: Automatic Adjustment X: No Automatic Adjustment

* “DETAIL” activates automatic long cable (skew, peaking) adjustment.

** Black level, RGB sharpness, RGB delay and RGB position are adjusted using “Long cable software”

which is included in the attached CD-ROM.

1 2 ... 20 21 22 23 24 25 26 27 28 29 30 31 32 33

Kommentare zu diesen Handbüchern

Keine Kommentare