NEC XM29 Bedienungsanleitung PDF herunterladen (Seite 10)

Terminal Board

DIP SW REMOTE

EXT SPEAKERS

SPEAKERS MUST HAVE

MORE THAN 5WATT RATING

IMPEDANCE 8 OHM

AC IN

SPEAKER SELECT

RIGHT LEFT

HIGH

INT EXT

BNC

R L(MONO)

AUDIO

VIDEO 1

1 2 3 4 5 6 7 8

HIGH

THROUGH

OUT

THROUGH

OUT

THROUGH

OUT

THROUGH

OUT

THROUGH

OUT

THROUGH

OUT

THROUGH

OUT

RGB1

PC / EXT CTL

HIGH

BNC

R L(MONO)

AUDIO

VIDEO 2

R/C

G/Y/Y B/C

OUT

H/CS V

L(MONO)

HIGH

RGB AUDIO RGB 2



H RGB 2

R/CR/PR, G/Y/Y, B/CB/PB/ H/CS and V IN (BNC) ... These are analog RGB and

component signal input terminals. Connect external components with R,

G, B, H, and V output terminals to these analog RGB input terminals. Be

sure that the RGB connection cable is correctly attached to the

corresponding terminals.

R/CR/PR, G/Y/Y, B/CB/PB/ ,H/CS and V THROUGH OUT (BNC)...... Connect to a

second monitor’s RGB inputs to relay the RGB signal inputs at R, G, B, H,

and V IN.

75 Ω/HIGH Impedance Select Switches for RGB and HV .... Set to “75 Ω”

during normal operation. In multiple connections using R, G, B, H and V IN

and OUT terminals, set to “HIGH” on all but the last monitor. Set to “75 Ω”

on the last monitor only.

I DIP Switch

DIP SW ..... This DIP switch sets Sync. Control, the Intelligent Power

Manager, external control on/off, remote control on/off, and OSM control

menu control on/off. See pages 17 and 18 for more details.

J REMOTE IN/OUT

Connect the optional remote cable, included with the optional remote

control, to the REMOTE IN terminal. The REMOTE OUT terminal is used

to connect several monitors together and allows all of the monitors to be

controlled by one remote control.

NOTE: Up to 50 monitors can be connected in the serial connection

(This can be done only when the supplied remote cable is used.).

K PC/EXT CTL IN(D-Sub 15-pin)

This terminal is used when power ON/OFF, input selection, AUDIO MUTE,

PICTURE MUTE, and DEGAUSS are operated externally (by external

control). See also page 46 for external control port pin assignments. You

can also use this connector to connect your PC to control the MultiSync

XP29 Xtra/XM29 Xtra monitor. This allows you to utilize your PC and serial

communication protocol to control the monitor.

NOTE: Select EXT. CONTROL ON by setting pin No. 6 of DIP SW to

the ON position when operating the monitor by external control.

NOTE: When in the EXT. CONTROL mode, the following operations of

the supplied wireless remote control are not possible: Power control

ON/ OFF, Input selection, and Degauss switch ON/OFF.

PC/EXT CTL OUT (D-Sub 15-pin) ..... Connect to a second monitor’ s PC/EXT

CTL input to relay the signal input at the PC/EXT CTL IN. The PC/EXT CTL

OUT terminal is used to connect several monitors together and allows all of

the monitors to be controlled by one external control. No. 6 pin (EXT.

CONTROL) of DIP SW must be set to the ON position on all of the

monitors.

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 39 40

Kommentare zu diesen Handbüchern

Keine Kommentare

NEC XM29 Bedienungsanleitung Seite 10

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Fernseher & Monitore NEC XM29